|
|
| (8 intermediate revisions by one user not shown) |
| Line 1: |
Line 1: |
| − | This page outlines some basic cost calculations I use in my vehicle sets, both pre-calculated spreadsheet numbers, and the code used for variable running costs in the game. When designing a set in a spreadsheet, it's probably best to use standard numbers first, then fudge values for vehicles which you think need to be more or less expensive.
| |
| | | | |
| − | ==Base Costs==
| |
| − | I use the following base costs:
| |
| − | *0F/4B8E for locomotive purchase, multiplier 08
| |
| − | *10/4B94 for wagon purchase, multiplier 0A
| |
| − | *2A/4C30 for locomotive running, multiplier 0B
| |
| − | *2B/4C36 for wagon running, multiplier 05
| |
| − |
| |
| − | The NFO looks like this:
| |
| − | <pre>
| |
| − | 1 * 7 00 08 01 01 0F 08 08 // loco cost
| |
| − | 1 * 7 00 08 01 01 10 08 0A // wagons cost
| |
| − | 1 * 7 00 08 01 01 2A 08 0B // running cost
| |
| − | 1 * 7 00 08 01 01 2B 08 05 // wagon running cost
| |
| − | </pre>
| |
| − |
| |
| − | __TOC__
| |
| − |
| |
| − | =Trains=
| |
| − | ==Locomotives==
| |
| − | ===Purchase Cost===
| |
| − | ====Steam Locomotives====
| |
| − | '''Weight in Tons * ProdCost'''
| |
| − | *''ProdCost'' is usually 0.25, but can be fudged between 0.2 and 0.3.
| |
| − |
| |
| − | *Example: [[4-6-0 Jubilee]], 126 * 0.25 = 32
| |
| − |
| |
| − | ====Diesel and Electric Locomotives====
| |
| − | '''Weight in Tons * ProdCost * (Horsepower / BaseHP )'''
| |
| − | *''ProdCost'' starts at 0.4 for early experimental diesels, 0.3 for 1960s production units, down to 0.22 for 21st century designs. Again, these numbers are fudgable if you think a particular vehicle should be more or less expensive. For electric locomotives, early vehicles are 0.5, and is down to 0.4 by the end of the century.
| |
| − | *''BaseHP'' is a "typical" power output for engines of that type/era. For diesels, I use 2000 for models designed before 1975, 2500 from 1975 to 1990, and 3000 after 1990. For large electrics, I use 4000.
| |
| − |
| |
| − | *Example: [[EE Type 3]], 107 * 0.3 * (1750 / 2000) = 28
| |
| − |
| |
| − | ===Running Cost===
| |
| − | '''(Horsepower * EffCost) / (SuspCost - MaxSpeed)'''
| |
| − | *''EffCost'' is the efficency of the design, where a higher number is worse; 5 for most steam locomotives, with a slight bonus (down to 4.5) for later very large locomotives in NARS. 3.75 for most diesels, down to 3.5 for modern designs. 3 for most electrics. Very powerful locomotives may need lower numbers and very underpowered vehicles (eg railbusses) may need higher numbers.
| |
| − | *''SuspCost'' represents the wear and tear on the traction system and track, and is a number roughly imagined as the speed at which the vehicle will fall apart. I use 200 for steam locomotives and 300 for modern electric locomotives, 225 for first generation diesels and 250 for modern diesels.
| |
| − |
| |
| − | *Example: [[4-6-0 Jubilee]], (1550 * 5) / (200 - 90) = 70
| |
| − | *Example: [[EE Type 3]], (1750 * 3.75) / (225 - 80) = 45
| |
| − |
| |
| − | ===Variable Running Cost===
| |
| − |
| |
| − |
| |
| − |
| |
| − | [[Catgory:NFO]]
| |
